DJ Amplifier Connector Details and Back Panel Settings
In the world of DJ Systems and sound engineering, the amplifier is a very important equipment. A DJ amplifier is like a powerhouse for sound. It takes the audio signals from a DJ mixer or other audio devices and makes them louder and clearer so everyone can hear the music better. For small setups where low-power speakers are used need low-power amplifiers but in large setups where high-power speakers are used need high-power amplifiers. While installing and operating a DJ setup you must know the DJ amplifier connector details and back panel settings.
The connectors on a DJ amplifier determine how you connect various audio devices such as mixers, DVDs, CDs, music players, microphones, and speakers to the amplifier. Different connectors, like RCA, XLR, TRS, or Speakon have different characteristics and are suitable for different types of audio equipment. Using the right connectors ensures proper signal transmission and minimizes interference or signal loss. Also, the back panel of a DJ amplifier typically houses various controls and settings that allow you to customize the sound output and adapt to different setups or venues.
Low Power DJ Amplifier Connector Details
In this range, basically, 400 watts to 1000 watts amplifiers come. This type of amplifier is used to drive Horns, HF drivers, etc.
Here are the below different connectors are explained below,
Speakon Connectors:
In the below Figure 01 the amplifier contains three speakon connectors 2Ω, 4Ω, and 8Ω for connecting speakers. It is remember to note that only one output 2Ω or 4Ω or 8Ω can be utilized at a time. These connectors ensure secure and reliable connections between the amplifier and speakers using Speakon cables to ensure optimal sound transmission.
Banana Connectors:
If you don't have Speakon cables or the speaker does not support Speakon then you can use Banana connectors as Alternative Connectors. It offers a versatile solution for connecting speakers using wires. Here you need to connect the negative terminal of the speaker to the Common terminal and the positive terminal of the speaker should be connected to anyone among 2Ω, 4Ω, or 8Ω as per your speaker ratings.
Output Voltage Compatibility:
For voltage-rated speakers such as Horns and HF drivers, the amplifier provides 70V and 100V output terminals. These terminals help to connect the amplifier with specialized speaker systems. Here you need to connect the negative terminal of the speaker to the Common terminal and the positive terminal of the speaker should be connected to anyone among 70V or 100V as per your speaker ratings.
Signal Input / Output:
Here you can see XLR and Jack connectors are available for signal input that offers multiple options for audio source integration. If you have XLR cables then you can use XLR and if you don't have XLR then you can use Jack connectors. You can also see near the signal input connectors the Link or output connectors also given. Using these connectors you can connect another amplifier to the same input signals.
Pre-Amp Connector:
It is used to connect External recorders.
Auxiliary Inputs:
Aux-1 and Aux-2 connectors are used for connecting various music players such as mobile phones and laptops, ensuring a diverse range of audio sources.
Powering Your Amplifier:
Without power, the amplifier remains silent. The AC power plug must be connected to a 240V AC power supply to operate the amplifier. In case, where AC power is unavailable, the 24V DC terminals offer an alternative power input source where you can connect batteries or external DC supplies.
Reset Switch:
The reset button provides a quick solution for resetting the amplifier, ensuring smooth operation during events or performances.
Earthing Terminal:
The earthing terminal is used to connect the amplifier to the ground or earth to protect against electric shock by providing a direct path to the ground.
High Power DJ Amplifier Connector Details & Backside Settings
In this range, basically, 1000 watts to 10000 watts or more amplifiers come. This type of amplifier is used to drive high-power speakers such as Woofers, Subwoofers, etc.
Here are the below different connectors and back panel settings are explained below,
Signal Input / Output:
Here, Female XLR Connectors are used for Amplifier Input.
CH1 Input connector for Input to the Channel 1 Module of the Amplifier and the CH2 Input Connector for Input to the Channel 2 Module of the Amplifier.
The Male XLR Connectors are used for connecting another amplifier to the same input signals. The CH1 Link Connector is linked to Channel 1 Input and the CH2 Link Connector is linked to Channel 2 Input. Remember that different amplifiers from different manufacturers may have different connectors for signal input and output such as RCA, 6.5mm Jack, etc.
Amplifier Output:
Here Speakon connectors and Banana Connectors can be used alternatively to connect speakers to the amplifier. The Speakon CH1 Output provides channel 1 output and the Speakon CH2 Output provides channel 2 output.
Remember that In the Bridge Mode, all the amplifiers provide output through anyone channel output(here Channel 1 in fig.02). So check identification on your amplifier whether it provides bridge output through channel 1 output or channel 2 output. If you are using banana connectors, then also identify the terminals that provide bridge output(mentioned on the amplifier). In this amplifier shown in the figure.02, the Positive terminal of channel 1 and the negative terminal of channel 2 provides the bridge output.
Back Panel Settings:
LIMITER: The limiter switch is used to prevent signal peaks from exceeding a certain level, thereby protecting the speakers from damage due to overloading. It effectively limits the maximum output level of the amplifier, ensuring that the audio signal stays within safe bounds.
SENSITIVITY: Sensitivity controls the input level at which the amplifier begins to amplify the signal. It allows you to adjust the amplifier's response to different input signal strengths, optimizing performance for various audio sources.
OPERATION MODE: This setting determines how the amplifier channels are configured and how they interact with each other.
Stereo mode: Each channel operates independently, delivering separate left and right signals to two separate speaker systems. In this mode, the amplifier needs two inputs for two channels - left and right.
Parallel mode: In this mode, both amplifier channel inputs are linked together so the amplifier needs only one input for any one channel and both channels will provide output.
Bridge mode: In this mode, both amplifier channel outputs are combined to deliver a single and more powerful output to a single speaker or speaker load. Here also, the amplifier needs a single input in anyone channel input(generally channel 1).
FILTER: The filter setting allows you to apply a frequency filter to the audio signal, adjusting the range of frequencies that are passed through the amplifier. If you put the switch at High the amplifier will give output only high-frequency signal, If you put the switch at Low the amplifier will give output only low-frequency signal, and If you put the switch at Bypass the amplifier will give output as same frequency as the input signal.
HIGH CUT: If you turn it On, the amplifier will provide Low-frequency output signals only that are used to drive woofers and subwoofers.
LOW CUT: If you turn it On, the amplifier will provide High-frequency output signals only that are used to drive HF Drivers or speakers.
Read Also:
DJ Amplifier Connector Details and Back Panel Settings
Reviewed by Author
on
April 13, 2024
Rating:
Reviewed by Author
on
April 13, 2024
Rating: